Mytek Protools-HD DIO Card – User Manual Mytek Protools HD DIO CardUser Manual ver. 1.1 / Oct 2010© Mytek 2006
Mytek Protools-HD DIO Card – User Manual 7. Attach card ribbon cable to DIOCARD1 connector on the mainboard.8. Gently push the card i
Mytek Protools-HD DIO Card – User Manual 9. Screw in converter top cover.10. Connect power and signal lines.11. Turn the converter on
Mytek Protools-HD DIO Card – User Manual Connecting Clock Signal LineSingle converterIf a single converter is used in the system, cho
Mytek Protools-HD DIO Card – User Manual Multiple convertersA Protools HD system can accept up to two converters connected to each ca
Mytek Protools-HD DIO Card – User Manual Input ConnectionThe Protools DIO-HD card features two connectors: Primary Port and Expansio
Mytek Protools-HD DIO Card – User Manual Signal RoutingWhile Protools software allows for up to 16 channels of input or output, only
Mytek Protools-HD DIO Card – User Manual OutputTo playback signal from Protools to the converter's analog outputs DIOCARD 1 SOUR
Mytek Protools-HD DIO Card – User Manual Launch and ConfigurationAfter the card installation in the converter, and after each hardwar
Mytek Protools-HD DIO Card – User Manual 6. Select each converter and press Set to Default to set the application in the normal work
Mytek Protools-HD DIO Card – User Manual Typical ConfigurationsSingle 8x192 ADDA converter1. Connect the 8X192 ADDA (through Primary
Mytek Protools-HD DIO Card – User Manual This manual may be updatedDownload the newest version at:http://www.mytekdigital.com/documents l
Mytek Protools-HD DIO Card – User Manual 6. If hardware configuration was changed, open Setup > Hardware Setup and press Set To De
Mytek Protools-HD DIO Card – User Manual 11. In the editing panel assign input and output channels according to the I/O Setup configu
Mytek Protools-HD DIO Card – User Manual Two 8x192 ADDA converters, first on internal clock (clock master), second as slave1. Connect
Mytek Protools-HD DIO Card – User Manual 8. Open Setup > Hardware Setup and check: ✔ Are 8X192 ADDA Mytek Digital converters prope
Mytek Protools-HD DIO Card – User Manual 12. Use SOURCE TO DIGITAL OUT and SOURCE TO ANALOG OUT buttons to set desired signal flow i
Mytek Protools-HD DIO Card – User Manual 14. In the editing panel assign input and output channels, according to the I/O Setup config
Mytek Protools-HD DIO Card – User Manual Software updateWARNING!Remember to follow basic safety rules about the handling of electroni
Mytek Protools-HD DIO Card – User Manual 3. Locate the memory socket on the converter main board.4. Gently remove old memory chip.To
Mytek Protools-HD DIO Card – User Manual 5. Carefully insert new memory chip in the socket. The chip slot (pin1) should be matching t
Mytek Protools-HD DIO Card – User Manual 7. Attach power cord and other cabling.8. Turn on the converter.For about 2 seconds no LED&a
Mytek Protools-HD DIO Card – User Manual ContentContent...
Mytek Protools-HD DIO Card – User Manual IntroductionThe Mytek Protools-HD DIO Card is a physical card that plugs into the back of th
Mytek Protools-HD DIO Card – User Manual Quick Start1. DIO-HD card installationRemove the top cover from the converter, unscrew DIOCA
Mytek Protools-HD DIO Card – User Manual 5. Routing configuration within converters The Mytek 8X192 ADDA SOURCE TO DIGITAL OUT define
Mytek Protools-HD DIO Card – User Manual Card InstallationOnly a single Protools-HD DIO Card can be installed in one converter. A dif
Mytek Protools-HD DIO Card – User Manual 3. Remove top cover.4. Locate the DIOCARD1 expansion slot on the mainboard.User Manual ver.
Mytek Protools-HD DIO Card – User Manual 5. Unscrew cover plate of DIOCARD1 slot from the rear panel.6. Partially insert the card fr
Commentaires sur ces manuels